Type: surface mounted PIR motion sensor
Rated power: 1200W
Voltage: 220-240V
Ingress Protection: IP44
Model number: OR-CR-204
Colour: Black, White
Detection distance: 12m
Detection angle: 180°
Power consumption: 0.45W (ON); 0.1W (OFF)
We are away from 23rd June to 30th June. All new orders will be shipped after the 30th of June. We are sorry for the inconvenience.
ORNO PIR motion sensor 1200W IP44 OR-CR-204
• passive infrared sensor
• used to automatically control lighting or other electrical devices
• for indoor and outdoor use
• works with LED lighting
• mechanical vertical adjustment
• adjustable: light time (LUX) and light intensity (LUX)
• available colours: white, black
This ORNO sensor adopts high sensitivity detector, integrated circuit and SMT; It gathers automatic, convenient, safe, energy-saving, practical functions; It has wide detection range made up of up and down, left and right service field. Switch on automatically when someone enters the range of PIR motion sensor. Enables connected lights to switch on automatically light then stays on until the person leaves the range and then switches itself off when the range of the sensor is unoccupied. The sensor reflects the latest development in outdoor lighting technology and provides close to zero energy wastage in terms of lights being on unnecessarily with the ability to adjust the timing 2-7 minutes and adjust the level of ambient light intensity at which the device operated. It can identify day and night automatically; It is easy to install and its usage is wide; It has the function of power indication and detection indication. If that is not what you are looking for then please have a look at other motion sensors in our store.
FUNCTION:
Identify day and night automatically: The ambient light of ST09 could be adjusted according to your desire: when turning to SUN (max), it will work day and night, when turning it to MOON (min), it will only work in the ambient light less than 3LUX. As for adjustment, please refer to testing way. Time-delay is added continually: When it receives the second induction signals after the first induction, it will compute time once more on the rest of the first time-delay basis (set time). Time-delay is adjustable: It can be set according to your desire, the minimum is 10sec±3sec, and the maximum is 7min±2min.
TEST:
Turn time knob anti-clockwise to the minimum; turn the LUX knob clockwise to the maximum (SUN), Switch on power, the controlled load should not work, needing to preheat within 5-30sec. The sensor will be sensed again in 5-10sec later when the first induction is finished; the load should work when received the sensor signal and stop working within 7-13sec with no any sensor signal. Turn LUX knob to minimum anti-clockwise, if you test it when the ambient light is more than 3LUX, the induction load would not work after the load stops working; the load should work if you cover the detection window with an opaque object (towel etc), it would be regular the load stops to work within 7-13sec under no induction signal condition.
Note: when testing in daylight, please turn LUX knob to (SUN) position, otherwise the sensor lamp could not work!
INSTALLATION:
(see the picture below)
• Switch off the power.
• Loosen the screw on the bottom lid, open the wiring hole, pass the wire of power and load through the bottom lid.
• Fix the bottom lid with inflated screw in the selected position.
• Connect the power and load wire into connection-wire column according to the connecting figure.
• Put the sensor on the bottom lid, twist the screw tightly then electrify it and test it.
ORNO PIR motion sensor 1200W IP44 OR-CR-204 specification
Voltage: | ~230V/50Hz |
Ambient Light: | 3-2000 LUX (adjustable) |
Detection Distance [m]: | 12 |
Colour: | Black, White |
Working Humidity: | <93%RH |
IP rating: | IP44 |
Detection Range: | 180° |
Time-Delay: | min: 10sec±3sec; max: 7min±2min |
Dimensions [mm]: | H91,6 x L84,6 x W63,4 |
Power consumption: | 0.45W (work); 0.1W (static) |
Installation Height [m]: | 2-4 |
Weight [kg]: | 0.186 |
Power Frequency: | 50Hz |
Rated Load: | 1200W (incandescent) 300W (LED) |
LED lights compatible: | Yes |
Working Temperature: | -20°C~+40°C |
Detection Motion Speed [m/s]: | 0.6 ~1.5 |
Warranty: | 2 years |
ORNO PIR motion sensor 1200W IP44 OR-CR-204 package includes
1 x PIR motion sensor in a retail packaging
2 x Screws
2 x Plastic wall plugs (for the screws)
1 x Manuals
Data sheet
- Rated Voltage
- 230V
- Certification
- CE
RoHS
- Warranty
- 2 years
- Pack Quantity
- 1
- Packaging
- Original retail colour packaging
- Instructions
- English
- Country/Region Of Manufacture
- China
- Type Of Material
- Plastic
- Current Type
- AC
- Power Source
- Hardwired mains
- Class
- Light Switches
- Unit Type
- Unit
Specific References
- ean13
- 5901752481060
- mpn
- P1126